/* gcbca_co_nhA.c Notes from NMRFAM: - HIFI for adding HIFI experiments added - N15 dimension modified to allow semi-constant time evolution - on spectrometers running older version of vnmr, the pulse sequence may fail to compile because the system is unable to recognize the "psg_abort" command. If this is the case, replace all the "psg_abort" commands with "abort" commands (these will not compile on spectrometers with the new VNMRS console). ********************************************************************************** NOTES FOR ABOUT THE COHERENCE SELECTION GRADIENTS: at NMRFAM, we have found that using a longer decoding gradient, gt2, 500us instead of 200us, results in a better suppression of the water signal (especially in coldprobes). Thus, the values we use by default are: gt1=.0023 gzlvl1=28000 gt2=.0005 gzlvl2~=13060 gzlvl2 needs to be optimized for each spectrometer. We recommend using the HNCO experiment for optimizating gzlvl2 and then use the same value for all these sequences. An easy way of doing this is by adding the following lines to the probefile, "$userdir/probes/HCN/HCN" : N15mt_gt2 0.00050 N15mt_gt1_3D 0.0023 N15mt_gzlvl1_3D 28000 N15mt_gzlvl2_3D 13070 "write the optimized value here" these can be added at the end of the N15 section. If these lines are NOT found, the default BioPack parameters will be loaded from the probefile. You can also set these parameters by hand after loading the sequence. ********************************************************************************** NOTES FOR RUNNING HIFI NMR: to run HIFI experiments you can either use HIFI='t' or HIFI='s'. HIFI='t' the angle of the tilted plane can be specified directly using the parameter tilt, e.g.: tilt=45 to record a 45 degrees tilted plane. The tilted plane is then obtained by dividing sw1/cos(tilt) and sw2/sin(tilt) and evolving both dimensions simultaneously, point by point. NOTE: this is the option that is used when running HIFI. HIFI='s' both dimensions are evolved simultaneously by using the sw1 and sw2 values as entered. The tilted angle can then be calculated from the ratio between sw1/sw2 (the paramter tilt is not used and is IGNORED). Since for HIFI spectra both indirect dimensions are evolved simultaneously, the same number of increments (ni) is used for both dimensions. Note: ni2 is not used and it MUST be set to 0. Similarly, to start both indirect dimensions at half of the dwell-time, set f1180='y' (f2180 is not used and is IGNORED). You can either start BOTH indirect dimensions at time zero (f1180='n') or at half of the dwell-time (f1180='y'). Starting one dimension at half of the dwell-time and the other at zero will result in an un-phaseable spectrum and thus is NOT allowed. To obtain quadrature detection for both indirect dimensions, both phase and phase2 MUST be used by typing: phase=1,2 phase2=1,2 . Make sure that phase is arrayed before phase2, so that the order of the array will be : array='phase,phase2' You can also set the order of the array directly by typing: array='phase,phase2' Thus, to record a 50degree tilted plane with 64 increments in the indirect dimension (16 dummy scans, 8 scans per increment and starting the first point at half dwell time), the parameters are: ss=16 nt=8 HIFI='t' tilt=50 ni=64 phase=1,2 phase2=1,2 f1180='y' (ni2=0, f2180=IGNORED) ********************************************************************************** 3D CBCA(CO)NH gradient sensitivity enhanced version. Correlates Cb(i),Ca(i) with N(i+1), NH(i+1). Uses constant time evolution for the CaCb shifts and for the 15N shifts. Standard features include maintaining the 13C carrier in the CaCb region throughout using off-res SLP pulses; full power square pulses on 13C initially when 13CO excitation is irrelevant; square pulses on the Ca and CaCb with first null at 13CO; one lobe sinc pulses on 13CO with first null at Ca; shaka6 composite 180 pulse to simultaneously refocus Ca and invert CO; optional 2H decoupling when CaCb magnetization is transverse for 4 channel spectrometers. Magic-angle option for coherence transfer gradients. TROSY option for N15/H1 evolution/detection. pulse sequence: Grzesiek and Bax, JACS 114 6291, 1992. SLP pulses: J Magn. Reson. 96, 94-102 (1992) shaka6 composite: Chem. Phys. Lett. 120, 201 (1985) TROSY: JACS, 120, 10778 (1998) Written by Lewis Kay 09/15/92 Modified by L.E.K 11/24/92 to include enhanced pfg and shaped C' pulses Modified by L.E.K. 01/03/93 to reduce phase cycle by adding gradients in the t1 evolution constant time domain. H decoupling now begins in the interval immediately following the t1 evolution domain. Modified by G.G 10/14/93 to permit DPS and remove gate (comments such as "point g" refer to pulse sequence diagram in reference) Modified extensively by M Robin Bendall, Varian, March 1994 and March 95 to include the above standard features. Revised and improved to a standard format by MRB, BKJ and GG for the BioPack, January 1997. TROSY added Dec 98, based on similar addition to gNhsqc. (Version Dec 1998). Auto-calibrated version, E.Kupce, 27.08.2002. CHOICE OF DECOUPLING AND 2D MODES Set dm = 'nnn', dmm = 'ccc' Set dm2 = 'nny', dmm2 = 'ccg' (or 'ccw', or 'ccp') for 15N decoupling. Set dm3 = 'nnn' for no 2H decoupling, or 'nyn' and dmm3 = 'cwc' for 2H decoupling. Must set phase = 1,2 and phase2 = 1,2 for States-TPPI acquisition in t1 [13C] and t2 [15N]. The flag f1180/f2180 should be set to 'y' if t1/t2 is to be started at halfdwell time. This will give 90, -180 phasing in f1/f2. If it is set to 'n' the phasing should be 0,0 and will still give a perfect baseline. Thus, set f1180='n' for (0,0) in 13C and f2180='n' for (0,0) in 15N. f1180='y' is ignored if ni=0, and f2180='y' is ignored if ni2=0. DETAILED INSTRUCTIONS FOR USE OF gcbca_co_nh 1. Obtain a printout of the Philosopy behind the BioPack development, and General Instructions using the macro: "printon man('BioPack') printoff". These Detailed Instructions for gcbca_co_nh may be printed using: "printon man('gcbca_co_nh') printoff". 2. Apply the setup macro "gcbca_co_nh". This loads the relevant parameter set and also sets ni=ni2=0 and phase=phase2=1 ready for a 1D spectral check. 3. The two C13 180 degree pulses between points c and d have been replaced by a single 6-pulse composite dubbed "shaka6" which povides near perfect refocusing with no phase roll over the Cab region and near perfect inversion over the CO region 18kHz off-resonance provided pwC < 20 us in a 600 MHz system. 4. Centre H1 frequency on H2O (4.7ppm), C13 frequency on 46ppm, and N15 frequency on the amide region (120 ppm). The C13 frequency remains at 46ppm, ie at CaCb throughout the sequence. 5. The H1 frequency is NOT shifted to the amide region during the sequence. H1 decoupling is controlled by the waltzB1 parameter. 6. The parameter phi7cal (listed in dg and dg2) is provided to adjust the phase of the last 90 degree C13 pulse, which is phase-shifted by the prior 180 degree pulse on the Ca region and by the use of SLP pulses on the CO region. The experimentally determined value of this phase is also very sensitive to small timing differences (microseconds) between the two theta delays. Check this phase via 1D spectra - maximise signal, or for greater accuracy obtain the value for a null and then add or subtract 90 degrees. The value must be a positive number. It needs to be calibrated once only for each spectrometer and the gc_co_nh and gcbca_co_nh pulse sequences. 7. tauCH (1.7 ms) and timeTN (14 ms) were determined for alphalytic protease and are listed in dg2 for possible readjustment by the user. 8. The coherence-transfer gradients using power levels gzlvl1 and gzlvl2 may be either z or magic-angle gradients. For the latter, a proper /vnmr/imaging/gradtable entry must be present and syscoil must contain the value of this entry (name of gradtable). The amplitude of the gzlvl1 and gzlvl2 should be lower than for a z axis probe to have the x and y gradient levels within the 32k range. For any value, a dps display (using power display) shows the x,y and z dac values. These must be <=32k. 9. TROSY: Set TROSY='y' and dm2='nnn' for a TROSY spectrum of the bottom right peak of the 2D coupled NH quartet (high-field H1, low-field N15). The TROSY spectrum gives 50% S/N compared to the decoupled spectrum for a small peptide. To select any of the other three peaks of the 2D coupled quartet, in a clockwise direction from bottom right, change t4/t10 from x/y to x/-y to -x/-y to -x/y. NOTE, the phases of the SE train are almost the same as those determined for the gNhsqc sequence. The major difference is that kappa is eliminated compared to normal gcbca_co_nh so the N15 magnetization has not evolved with respect to the attached H's. I.e. the N15 state would be Ix rather than IySz if there was no coherence gradient - this imparts a 90 degree shift so t8 is changed to y (from x in the normal spectrum). Also gzlvl1 is after the 180 N15 pulse rather than before as in gNhsqc, so the sign of icosel and the t4/t10 phase2 increments are also swapped compared to gNhsqc. 10. The autocal and checkofs flags are generated automatically in Pbox_bio.h If these flags do not exist in the parameter set, they are automatically set to 'y' - yes. In order to change their default values, create the flag(s) in your parameter set and change them as required. The available options for the checkofs flag are: 'y' (yes) and 'n' (no). The offset (tof, dof, dof2 and dof3) checks can be switched off individually by setting the corresponding argument to zero (0.0). For the autocal flag the available options are: 'y' (yes - by default), 'q' (quiet mode - suppress Pbox output), 'r' (read from file, no new shapes are created), 's' (semi-automatic mode - allows access to user defined parameters) and 'n' (no - use full manual setup, equivalent to the original code). */ #include #include #include "Pbox_bio.h" /* Pbox Bio Pack Pulse Shaping Utilities */ static int /* T is for TROSY='y', phx etc also enable TROSY phase changes */ phx[1]={0}, phy[1]={1}, phi5[2] = {0,2}, phi6[2] = {2,0}, phi9[8] = {0,0,1,1,2,2,3,3}, rec[4] = {0,2,2,0}, recT[2] = {3,1}; static double d2_init=0.0, d3_init=0.0; static double H1ofs=4.7, C13ofs=46.0, N15ofs=120.0, H2ofs=0.0; static shape offC1, offC2, offC4, offC5, offC7; pulsesequence() { /* DECLARE AND LOAD VARIABLES */ char f1180[MAXSTR], /* Flag to start t1 @ halfdwell */ f2180[MAXSTR], /* Flag to start t2 @ halfdwell */ mag_flg[MAXSTR], /* magic-angle coherence transfer gradients */ TROSY[MAXSTR]; /* do TROSY on N15 and H1 */ int icosel, /* used to get n and p type */ t1_counter, /* used for states tppi in t1 */ t2_counter, /* used for states tppi in t2 */ ni = getval("ni"), ni2 = getval("ni2"); double tau1, /* t1 delay */ tau2, /* t2 delay */ N15counter,N15incr,halfT2,t2a,t2b,CTdelay, tauCH = getval("tauCH"), /* 1/4J delay for CH */ timeTN = getval("timeTN"), /* constant time for 15N evolution */ timeCH = 1.1e-3, /* other delays */ timeAB = 3.3e-3, zeta = 3.0e-3, eta = 4.6e-3, theta = 14.0e-3, kappa = 5.4e-3, lambda = 2.4e-3, bw, ofs, ppm, /* temporary Pbox parameters */ pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */ pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */ rf0, /* maximum fine power when using pwC pulses */ /* 90 degree pulse at Cab(46ppm), first off-resonance null at CO (174ppm) */ pwC1, /* 90 degree pulse length on C13 at rf1 */ rf1, /* fine power for 5.1 kHz rf for 600MHz magnet */ /* 180 degree pulse at Cab(46ppm), first off-resonance null at CO(174ppm) */ pwC2, /* 180 degree pulse length at rf2 */ rf2, /* fine power for 11.4 kHz rf for 600MHz magnet */ /* the following pulse lengths for SLP pulses are automatically calculated */ /* by the macro "biocal". SLP pulse shapes, "offC4" etc are called */ /* directly from your shapelib. */ pwC4, /*180 degree pulse at Ca(56ppm) null at CO(174ppm) */ pwC5, /* 90 degree selective sinc pulse on CO(174ppm) */ pwC7, /* 180 degree selective sinc pulse on CO(174ppm) */ rf4, /* fine power for the pwC4 ("offC4") pulse */ rf5, /* fine power for the pwC5 ("offC5") pulse */ rf7, /* fine power for the pwC7 ("offC7") pulse */ compH = getval("compH"), /* adjustment for C13 amplifier compression */ compC = getval("compC"), /* adjustment for C13 amplifier compression */ phi7cal = getval("phi7cal"), /* phase in degrees of the last C13 90 pulse */ pwH, /* H1 90 degree pulse length at tpwr1 */ tpwr1, /* 7.3 kHz rf for DIPSI-2 */ DIPSI2time, /* total length of DIPSI-2 decoupling */ ncyc_dec, waltzB1=getval("waltzB1"), pwNlvl = getval("pwNlvl"), /* power for N15 pulses */ pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */ sw1 = getval("sw1"), sw2 = getval("sw2"), gt1 = getval("gt1"), /* coherence pathway gradients */ gt2, gzcal = getval("gzcal"), /* g/cm to DAC conversion factor */ gzlvl1 = getval("gzlvl1"), gzlvl2 = getval("gzlvl2"), gt0 = getval("gt0"), /* other gradients */ gt3 = getval("gt3"), gt4 = getval("gt4"), gt5 = getval("gt5"), gt7 = getval("gt7"), gt8 = getval("gt8"), gstab = getval("gstab"), gzlvl0 = getval("gzlvl0"), gzlvl3 = getval("gzlvl3"), gzlvl4 = getval("gzlvl4"), gzlvl5 = getval("gzlvl5"), gzlvl6 = getval("gzlvl6"), gzlvl7 = getval("gzlvl7"), gzlvl8 = getval("gzlvl8"); /* call up HIFI code */ #include N15incr=T2incr; N15counter=T2counter; /* allow user to customize gt2 value */ if (find("gt2") > 0) gt2 = getval("gt2"); else gt2 = 0.1*gt2; /* defined withing HIFI.h getstr("f1180",f1180); getstr("f2180",f2180); */ getstr("mag_flg",mag_flg); getstr("TROSY",TROSY); /* LOAD PHASE TABLE */ settable(t3,1,phx); settable(t4,1,phx); settable(t5,2,phi5); settable(t6,2,phi6); if (TROSY[A]=='y') {settable(t8,1,phy); settable(t9,1,phx); settable(t10,1,phy); settable(t11,1,phx); settable(t12,2,recT);} else {settable(t8,1,phx); settable(t9,8,phi9); settable(t10,1,phx); settable(t11,1,phy); settable(t12,4,rec);} /* INITIALIZE VARIABLES */ if( dpwrf < 4095 ) { printf("reset dpwrf=4095 and recalibrate C13 90 degree pulse"); psg_abort(1); } if( pwC > 24.0e-6*600.0/sfrq ) { printf("increase pwClvl so that pwC < 24*600/sfrq"); psg_abort(1); } /* maximum fine power for pwC pulses */ rf0 = 4095.0; setautocal(); /* activate auto-calibration flags */ if (autocal[0] == 'n') { /* 90 degree pulse on Cab, null at CO 128ppm away */ pwC1 = sqrt(15.0)/(4.0*128.0*dfrq); rf1 = (compC*4095.0*pwC)/pwC1; rf1 = (int) (rf1 + 0.5); /* 180 degree pulse on Cab, null at CO 128ppm away */ pwC2 = sqrt(3.0)/(2.0*128.0*dfrq); rf2 = (4095.0*compC*pwC*2.0)/pwC2; rf2 = (int) (rf2 + 0.5); /* 180 degree pulse on Ca, null at CO 118ppm away */ pwC4 = getval("pwC4"), rf4 = (compC*4095.0*pwC*2.0)/pwC4; rf4 = (int) (rf4 + 0.5); /* 90 degree one-lobe sinc pulse on CO, null at Ca 118ppm away */ pwC5 = getval("pwC5"), rf5 = (compC*4095.0*pwC*1.69)/pwC5; /* needs 1.69 times more */ rf5 = (int) (rf5 + 0.5); /* power than a square pulse */ /* 180 degree one-lobe sinc pulse on CO, null at Ca 118ppm away */ pwC7 = getval("pwC7"), rf7 = (compC*4095.0*pwC*2.0*1.65)/pwC7; /* needs 1.65 times more */ rf7 = (int) (rf7 + 0.5); /* power than a square pulse */ } else /* if autocal = 'y', 'q', or 's' */ { if(FIRST_FID) /* call Pbox */ { ppm = getval("dfrq"); bw = 128.0*ppm; ofs = 128.0*ppm; offC1 = pbox_Rcal("square90n", bw, compC*pwC, pwClvl); offC2 = pbox_Rcal("square180n", bw, compC*pwC, pwClvl); bw = 118.0*ppm; offC5 = pbox_make("offC5", "sinc90n", bw, ofs, compC*pwC, pwClvl); offC7 = pbox_make("offC7", "sinc180n", bw, ofs, compC*pwC, pwClvl); ofs = 10.0*ppm; offC4 = pbox_make("offC4", "square180n", bw, ofs, compC*pwC, pwClvl); if (dm3[B] == 'y') H2ofs = 3.2; ofs_check(H1ofs, C13ofs, N15ofs, H2ofs); } pwC1 = offC1.pw; rf1 = offC1.pwrf; pwC2 = offC2.pw; rf2 = offC2.pwrf; pwC4 = offC4.pw; rf4 = offC4.pwrf; pwC5 = offC5.pw; rf5 = offC5.pwrf; pwC7 = offC7.pw; rf7 = offC7.pwrf; /* Example of semi-automatic calibration - use parameters, if they exist : if ((autocal[0] == 's') || (autocal[1] == 's')) { if (find("pwC1") > 0) pwC1 = getval("pwC1"); if (find("rf1") > 0) rf1 = getval("rf1"); } */ } /* power level and pulse times for DIPSI 1H decoupling */ DIPSI2time = 2.0*3.0e-3 + 2.0*14.0e-3 + 2.0*timeTN - 5.4e-3 + 0.5*pwC1 + 2.0*pwC5 + 5.0*pwN + 2.0*gt3 + 1.0e-4 + 4.0*GRADIENT_DELAY + 2.0*POWER_DELAY + 8.0*PRG_START_DELAY; pwH=1.0/(4.0*waltzB1); ncyc_dec = (DIPSI2time*90.0)/(pwH*2590.0*4.0); ncyc_dec = (int) (ncyc_dec +0.5); pwH = (DIPSI2time*90.0)/(ncyc_dec*2590.0*4.0); /* adjust pwH */ tpwr1 = 4095.0*(compH*pw/pwH); tpwr1 = (int) (2.0*tpwr1 + 0.5); /* x2 because obs atten will be reduced by 6dB */ /* CHECK VALIDITY OF PARAMETER RANGES */ if (timeAB -0.5*(ni-1)/sw1 -gt4 -WFG_START_DELAY -pwC7 < 0.2e-6) { text_error(" ni is too big. Make ni equal to %d or less.\n", (int)((timeAB -gt4 -WFG_START_DELAY -pwC7)*2.0*sw1)+1); psg_abort(1);} /*** with semi-constant time N15 evolution this is no longer true if ( 0.5*ni2*1/(sw2) > timeTN - WFG3_START_DELAY) { printf(" ni2 is too big. Make ni2 equal to %d or less.\n", ((int)((timeTN - WFG3_START_DELAY)*2.0*sw2))); psg_abort(1);} ***/ if ( dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' ) { printf("incorrect dec1 decoupler flags! Should be 'nnn' "); psg_abort(1);} if ( dm2[A] == 'y' || dm2[B] == 'y' ) { printf("incorrect dec2 decoupler flags! Should be 'nny' "); psg_abort(1);} if ( dm3[A] == 'y' || dm3[C] == 'y' ) { printf("incorrect dec3 decoupler flags! Should be 'nyn' or 'nnn' "); psg_abort(1);} if ( dpwr2 > 46 ) { printf("dpwr2 too large! recheck value "); psg_abort(1);} if ( pw > 20.0e-6 ) { printf(" pw too long ! recheck value "); psg_abort(1);} if ( pwN > 100.0e-6 ) { printf(" pwN too long! recheck value "); psg_abort(1);} if ( TROSY[A]=='y' && dm2[C] == 'y' ) { text_error("Choose either TROSY='n' or dm2='n' ! "); psg_abort(1);} /* PHASES AND INCREMENTED TIMES */ /* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */ if (phase1 == 2) tsadd(t3,1,4); if (TROSY[A]=='y') { if (phase2 == 2) icosel = +1; else {tsadd(t4,2,4); tsadd(t10,2,4); icosel = -1;} } else { if (phase2 == 2) {tsadd(t10,2,4); icosel = +1;} else icosel = -1; } /* Calculate modifications to phases for States-TPPI acquisition */ if(t1_counter % 2) { tsadd(t3,2,4); tsadd(t12,2,4); } if(t2_counter % 2) { tsadd(t8,2,4); tsadd(t12,2,4); } /* Set up constant semi-constant time evolution in N15 */ halfT2 = 0.5*(N15incr-1)/sw2; if(f2180[A]=='y') halfT2=halfT2+(0.25/sw2); CTdelay = timeTN +pwC7 +WFG_START_DELAY -SAPS_DELAY; if (halfT2 > CTdelay) /* if the number of points exceeds the constant time delay use semi-constant time evolution */ { t2b = ((halfT2 -CTdelay)/(N15incr -1)) *N15counter; t2a = CTdelay -tau2 +t2b; if(FIRST_FID && N15incr>1) printf("\nSemi-Constant-Time N15 evolution is being used\n"); } else /* constant time evolution */ { t2a = CTdelay -tau2; t2b = 0.0; if(FIRST_FID && N15incr>1) printf("\nConstant-Time N15 evolution is being used\n"); } if (t2a < 0.2e-6) t2a = 0.0; /*** uncomment to check t2a and t2b values printf("%d: t2a = %.12f", N15counter,t2a); printf(" ; t2b = %.12f\n", t2b); ***/ /* BEGIN PULSE SEQUENCE */ status(A); delay(d1); if ( dm3[B] == 'y' ) { lk_hold(); lk_sampling_off();} /*freezes z0 correction, stops lock pulsing*/ rcvroff(); obspower(tpwr); decpower(pwClvl); dec2power(pwNlvl); decpwrf(rf0); obsoffset(tof); txphase(zero); delay(1.0e-5); if (TROSY[A] == 'n') dec2rgpulse(pwN, zero, 0.0, 0.0); /*destroy N15 and C13 magnetization*/ decrgpulse(pwC, zero, 0.0, 0.0); zgradpulse(gzlvl0, 0.5e-3); delay(1.0e-4); if (TROSY[A] == 'n') dec2rgpulse(pwN, one, 0.0, 0.0); decrgpulse(pwC, zero, 0.0, 0.0); zgradpulse(0.7*gzlvl0, 0.5e-3); delay(5.0e-4); rgpulse(pw,zero,0.0,0.0); /* 1H pulse excitation */ decphase(zero); zgradpulse(gzlvl0, gt0); delay(tauCH - gt0); simpulse(2.0*pw, 2.0*pwC, zero, zero, 0.0, 0.0); txphase(one); decphase(t3); zgradpulse(gzlvl0, gt0); delay(tauCH - gt0); rgpulse(pw, one, 0.0, 0.0); zgradpulse(gzlvl3, gt3); txphase(zero); delay(2.0e-4); if ( dm3[B] == 'y' ) /* begins optional 2H decoupling */ { gt4=0.0; /* no gradients during 2H decoupling */ dec3rgpulse(1/dmf3,one,10.0e-6,2.0e-6); dec3unblank(); dec3phase(zero); delay(2.0e-6); setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3); } decrgpulse(pwC, t3, 0.0, 0.0); /* point a */ /* C13 EVOLUTION BEGINS */ decphase(zero); decpwrf(rf7); delay(tau1 +2.0*(pwC1-pwC)/PI -SAPS_DELAY -PWRF_DELAY); /* WFG3_START_DELAY */ sim3shaped_pulse("", "offC7", "", 0.0, pwC7, 2.0*pwN, zero, zero, zero, 0.0, 0.0); zgradpulse(gzlvl4, gt4); decpwrf(rf2); if ( pwC7 > 2.0*pwN) delay(timeCH -gt4 -2.0*GRADIENT_DELAY -pwC7 -WFG3_START_DELAY -PWRF_DELAY -2.0*pw); else delay(timeCH -gt4 -2.0*GRADIENT_DELAY -2.0*pwN -WFG3_START_DELAY -PWRF_DELAY -2.0*pw); rgpulse(2.0*pw,zero,0.0,0.0); delay(timeAB - timeCH); decrgpulse(pwC2, zero, 0.0, 0.0); zgradpulse(gzlvl4, gt4); decpwrf(rf7); delay(timeAB -tau1 -gt4 -2.0*GRADIENT_DELAY -2.0*PWRF_DELAY -WFG_START_DELAY -pwC7 -2.0e-6); /* WFG_START_DELAY */ decshaped_pulse("offC7", pwC7, zero, 0.0, 0.0); decpwrf(rf1); /* point b */ /* C13 EVOLUTION ENDS */ decrgpulse(pwC1, zero, 2.0e-6, 0.0); obspwrf(tpwr1); obspower(tpwr-6); /* POWER_DELAY */ obsprgon("dipsi2", pwH, 5.0); /* PRG_START_DELAY */ xmtron(); /* point c */ decpwrf(rf0); decphase(t5); delay(zeta - 2.0*POWER_DELAY - PRG_START_DELAY - 0.5*10.933*pwC); decrgpulse(pwC*158.0/90.0, t5, 0.0, 0.0); decrgpulse(pwC*171.2/90.0, t6, 0.0, 0.0); decrgpulse(pwC*342.8/90.0, t5, 0.0, 0.0); /* Shaka composite */ decrgpulse(pwC*145.5/90.0, t6, 0.0, 0.0); decrgpulse(pwC*81.2/90.0, t5, 0.0, 0.0); decrgpulse(pwC*85.3/90.0, t6, 0.0, 0.0); decpwrf(rf1); decphase(zero); delay(zeta - 0.5*10.933*pwC - 0.5*pwC1); /* point d */ decrgpulse(pwC1, zero, 0.0, 0.0); decphase(t5); decpwrf(rf5); if ( dm3[B] == 'y' ) /* turns off 2H decoupling */ { setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3); dec3rgpulse(1/dmf3,three,2.0e-6,2.0e-6); dec3blank(); lk_autotrig(); /* resumes lock pulsing */ } zgradpulse(gzlvl7, gt7); delay(2.0e-4); decshaped_pulse("offC5", pwC5, t5, 0.0, 0.0); /* point e */ decpwrf(rf4); decphase(zero); delay(eta); decshaped_pulse("offC4", pwC4, zero, 0.0, 0.0); decpwrf(rf7); dec2phase(zero); delay(theta - eta - pwC4 - WFG3_START_DELAY); /* WFG3_START_DELAY */ sim3shaped_pulse("", "offC7", "", 0.0, pwC7, 2.0*pwN, zero, zero, zero, 0.0, 0.0); decpwrf(rf5); decpwrf(rf5); initval(phi7cal, v7); decstepsize(1.0); dcplrphase(v7); /* SAPS_DELAY */ dec2phase(t8); delay(theta - SAPS_DELAY); /* point f */ decshaped_pulse("offC5", pwC5, zero, 0.0, 0.0); /* xxxxxxxxxxxxxxxxxx OPTIONS FOR N15 EVOLUTION xxxxxxxxxxxxxxxxxxxxx */ zgradpulse(gzlvl8, gt8); if (TROSY[A]=='y') { xmtroff(); obsprgoff(); obspwrf(4095.0); obspower(tpwr); txphase(t4); } decpwrf(rf7); decphase(zero); dcplrphase(zero); delay(gstab); dec2rgpulse(pwN, t8, 0.0, 0.0); /* N15 EVOLUTION BEGINS */ dec2phase(t9); delay(t2a); dec2rgpulse(2.0*pwN, t9, 0.0, 0.0); delay(t2b); decshaped_pulse("offC7", pwC7, zero, 0.0, 0.0); /* WFG_START_DELAY */ decpwrf(rf4); /* PWRF_DELAY */ if (TROSY[A]=='y') { if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1); else zgradpulse(gzlvl1, gt1); delay(timeTN -PWRF_DELAY -pwC4 -WFG_START_DELAY -gt1 -2.0*GRADIENT_DELAY); decshaped_pulse("offC4", pwC4, zero, 0.0, 0.0); delay(tau2); } else { dec2phase(t10); if ((tau2 -kappa -PRG_STOP_DELAY) > 0.2e-6) { delay(timeTN -SAPS_DELAY -PWRF_DELAY -pwC4 -WFG_START_DELAY); decshaped_pulse("offC4", pwC4, zero, 0.0, 0.0); delay(tau2 -kappa -PRG_STOP_DELAY); xmtroff(); obsprgoff(); if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1); else zgradpulse(gzlvl1, gt1); txphase(t4); obspwrf(4095.0); obspower(tpwr); delay(kappa -gt1 -2.0*GRADIENT_DELAY -SAPS_DELAY -POWER_DELAY -PWRF_DELAY); } else if ((kappa -tau2 -pwC4 -WFG_START_DELAY) < 0.2e-6) { delay(timeTN +tau2 -kappa -PRG_STOP_DELAY -SAPS_DELAY -PWRF_DELAY); xmtroff(); obsprgoff(); decshaped_pulse("offC4", pwC4, zero, 0.0, 0.0); if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1); else zgradpulse(gzlvl1, gt1); txphase(t4); obspwrf(4095.0); obspower(tpwr); delay(kappa -pwC4 -WFG_START_DELAY -gt1 -2.0*GRADIENT_DELAY -SAPS_DELAY -POWER_DELAY -PWRF_DELAY); } else if ((kappa -tau2 -pwC4 -WFG_START_DELAY -gt1 -2.0*GRADIENT_DELAY -SAPS_DELAY -POWER_DELAY -PWRF_DELAY) < 0.2e-6) { delay(timeTN +tau2 -SAPS_DELAY -PWRF_DELAY -kappa -PRG_STOP_DELAY); xmtroff(); obsprgoff(); delay(kappa -tau2 -pwC4 -WFG_START_DELAY); decshaped_pulse("offC4", pwC4, zero, 0.0, 0.0); if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1); else zgradpulse(gzlvl1, gt1); txphase(t4); obspwrf(4095.0); obspower(tpwr); delay(tau2 -gt1 -2.0*GRADIENT_DELAY -SAPS_DELAY -POWER_DELAY -PWRF_DELAY); } else { delay(timeTN +tau2 -SAPS_DELAY -PWRF_DELAY -kappa -PRG_STOP_DELAY); xmtroff(); obsprgoff(); if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1); else zgradpulse(gzlvl1, gt1); txphase(t4); obspwrf(4095.0); obspower(tpwr); delay(kappa -tau2 -pwC4 -WFG_START_DELAY -gt1 -2.0*GRADIENT_DELAY -SAPS_DELAY -POWER_DELAY -PWRF_DELAY); decshaped_pulse("offC4", pwC4, zero, 0.0, 0.0); delay(tau2); } } /* point g */ /* xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx */ if (TROSY[A]=='y') rgpulse(pw, t4, 0.0, 0.0); else sim3pulse(pw, 0.0, pwN, t4, zero, t10, 0.0, 0.0); txphase(zero); dec2phase(zero); zgradpulse(gzlvl5, gt5); if (TROSY[A]=='y') delay(lambda - 0.65*(pw + pwN) - gt5); else delay(lambda - 1.3*pwN - gt5); sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0); zgradpulse(gzlvl5, gt5); txphase(one); dec2phase(t11); delay(lambda - 1.3*pwN - gt5); sim3pulse(pw, 0.0, pwN, one, zero, t11, 0.0, 0.0); txphase(zero); dec2phase(zero); zgradpulse(gzlvl6, gt5); delay(lambda - 1.3*pwN - gt5); sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0); dec2phase(t10); zgradpulse(gzlvl6, gt5); if (TROSY[A]=='y') delay(lambda - 1.6*pwN - gt5); else delay(lambda - 0.65*pwN - gt5); if (TROSY[A]=='y') dec2rgpulse(pwN, t10, 0.0, 0.0); else rgpulse(pw, zero, 0.0, 0.0); delay(gt2 + 1.0e-4 +gstab - 0.5*pw + 2.0*GRADIENT_DELAY + POWER_DELAY); rgpulse(2.0*pw, zero, 0.0, rof1); dec2power(dpwr2); /* POWER_DELAY */ if (mag_flg[A] == 'y') magradpulse(icosel*gzcal*gzlvl2, gt2); else zgradpulse(icosel*gzlvl2, gt2); /* 2.0*GRADIENT_DELAY */ delay(gstab); rcvron(); statusdelay(C,1.0e-4 - rof1); if (dm3[B]=='y') lk_sample(); setreceiver(t12); }